Laser Measurement

AthleticFIELD allows laser measurement through BluetoothLE, TCP/IP, and Serial (Android only).

Supported Devices

Total Stations

  1. Mato MTS-602R
  2. GoWin TSK 202
  3. Sokkia SET5x
  4. South Station NTS-352R

Leica Handheld Lasers

NOTE: If measuring from the board, the laser and the prism must be at the same height and pointing straight at the laster.

We hope to implement Smart Horizontal Mode for the E7500i and X4 in the near future. This would allow you to use a tripod.

  1. Leica Disto D2
  2. Leica Disto E7500i
  3. Leica Disto X4

Connection Types

Serial (Android only)

AthleticLIVE highly recommends a serial connection between your total station and tablet for simplicity and ease of setup.

To connect a total station to an Android device via serial, you need a micro-USB or USB-C OTG adapter. Plug the serial cable from the total station into the OTG adapter, then connect the OTG adapter to your Android device.

When setting up a serial device in AthleticFIELD, you need to know Baud, Stop BIts, Parity, Data Bits, and Flow Control. These are the most common settings:

  • Baud: 9600
  • Stop Bits: 1
  • Parity: None
  • Data Bits: 8
  • Flow Control: None

Most devices seem to work with the "Auto" option. If yours doesn't work, please contact ben@athletic.net so we can add your adapter to the list.

TCP/IP

This setup works with iOS and Android devices. Because serial doesn't work with iOS, this is the best option for a hardwire connection between total stations and iOS devices.

Purchase the following for each iOS device you intend to use.

  1. POE Ethernet adapter for iOS (Amazon Link). We like this one because it doesn't turn off when the iOS devices lock or go to sleep
  2. POE Switch (may or may not need this depending on your networking setup) (Amazon Link)
  3. Lantronix DB9 to POE connector (Amazon Link)
  4. Male-to-Male Null Modem Adapter - needed because that particular DB9 to POE connector has its TX/RX pins reversed (Amazon Link)

This works by creating a mini-network between your total station and your device.

BluetoothLE

For Leica handheld lasers, we support connection via BluetoothLE.

To connect a device via BluetoothLE on the Laser Settings page:

  1. Enable Bluetooth and location on your device.
  2. Click Start Scan.
  3. Eventually, you should see your AirConsole or your Disto device.
  4. Click Stop Scan.
  5. Click "Connect" on the device. You'll see three dots. Once connection happens, the button will change to "Disconnect" and you'll see a green connection message.

NOTE: Previous versions of this documentation recommended purchasing an AirConsole to connect total stations to Android/iOS devices via BluetoothLE. This seemed to be too buggy, so we recommend using TCP/IP or Serial if at all possible.

Bluetooth Gotchas
  1. If your device moves over 20-25m away from the total station, you risk disconnects.
  2. If your device does disconnect, you should get a red warning asking you to reconnect.
  3. If a measurement fails, you can click a button to go back to the settings page and reconnect.

Laser Setup

  1. Open the app.
  2. Click on "Settings"
  3. Click on "Allow Laser Measurement"
  4. Click the back button at the top.
Connect to a Laser
  1. Click on Laser Settings.
  2. Set your options.
    1. Click "Active"
    2. Set your desireed Connection type
    3. Choose your Laser.
    4. Set Measure to Point to Point or Triangular.
    5. If using Bluetooth, choose the Receiver Type (AirConsole for total stations. Leica Disto otherwise).
  3. Click Save.
  4. Click "Test" in the bottom right.
  5. Click "Measure" in the bottom right. After a couple seconds, measurement data should appear.

Setup Throws Triangulation

Note: Triangular laser measurement only works for horizontal throws and for total stations at this time. It does not work with Leica Distos.

  1. From the Laser Settings page and after entering your laser settings, click "Setup Throws Triangulation"
  2. Select the appropriate circle radius.
  3. Click "Measure to Circle Center". After a couple seconds, you should see the measurement details.
  4. To ensure your measurement is correct, set your prism within the throwing area and measure with tape. Then, click "Test Measurement". Make sure the tape measurement and the app measurement correspond.

If you set the Circle Radius to Shot Put, this center circle measurement will work for all Shot Put events. If, for example, you change to a Discus event, the app will not let you take a laser measurement until you re-measure the center circle.

Setup Jumps Triangulation

Note: Triangular laser measurement only works for horizontal jumps and for total stations at this time. It does not work with Leica Distos.

  1. Download any desired events to the app.
  2. From the Laser Settings page and after entering your laser settings, click "Manage [Event Name] Jump Boards"
  3. From the board closest to the sand, measure the far edge and the near edge.
  4. For any other boards, select a point on the edge of the board closest to the sand and measure. The Offset is the distance from the front of board 1 to the front of the board just measured.

Setup Jump Rail Lasers

When using a rail system with multiple jump boards, allow AthleticFIELD to track the offset between each board and the pit.

NOTE: This only works for metric events.

Learn more about adding Jump Boards to a horizontal jumps event >

Configure Laser Settings

If you plan to send laser marks into the app, use the following settings. Regardless of your choice, you will be entering the raw value from the laser to the end of the rail into your app. Then, you will select a board and apply an offset to that raw value

  1. Active: Yes
  2. Connection: Bluetooth LE
  3. Measure Type: Jumps - Rail
  4. Enter offset in app: Yes

If you plan to enter marks into the app, use the following settings:

  1. Active: Yes
  2. Connection: None
  3. Measure Type: Jumps - Rail
  4. Enter offset in app: Yes

Setting Offsets

If you have already downloaded the round into the app, you can manage jump boards from the laser settings screen.

Rail Offset Instructions
  1. Make a mark in the sand.
  2. Use a measuring tape to measure from the takeoff board to the mark. Enter in the "Tape Measurement" field.
  3. Measure the same point with your laser. Enter in the "Laser Measurement" field.
  4. Offset = Tape Measurement - Laser Measurement. The app generates this automatically.
  1. Click save when finished

Operation

  1. When you enter an attempt, take a laser measurement.
  2. If there is no default board, select a board.
  3. Click "Apply Offset".
  4. The mark will be calculcated for you.
  5. Hit Save.
Gotchas
  1. If something happens and you need to start using tape, simply enter the tape mark, select a board, and do not click "Apply Offset". The app will ask if you meant to do that. Confirm and continue.
  2. The app will not let you enter a mark unless you select a board for the attempt.

Measure a mark in an event

  1. Check athletes in, then prepare to enter a mark for an athlete.
  2. Click the wand icon in the "Mark" header.
  3. Within a couple seconds, the mark should appear.


How helpful was this article?


Powered by HelpDocs (opens in a new tab)